The recognition of the interface connected to the control board is done with the reading of a code associated to each kind of board through U1, enabled by the SELDEV signal generated by the control board. With the printer open, paper roll and spacer removed, loosen the two screws on the inside of the Printer, as shown on the right. Chapter 4 MP TH. The printer is set up by factory default for most users. Page 48 – Verify if the mechanism plastic chassis pins where the sensor is connected image on the side are not broken, which would let the sensor out of its position, leading to its malfunction. Configure the tests to be performed. Package contents Remove the MP TH printer from the package and make sure that all components listed below are available, and that they are in perfect shape:

Uploader: Zolora
Date Added: 22 January 2015
File Size: 61.59 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 3317
Price: Free* [*Free Regsitration Required]

Bematech MP-4000 TH Service Manual

Chapter 1 Bematech MP TH mp0400 ideal printing solution for your retail outlet, operating with high quality, high speed and reliability with reduced operation cost. Got it, continue to print. Problem There is no power in the electric outlet.

Paper dust congestion, generated by the cutter itself can also cause malfunction. The next steps are required in order to bemaech the thermal print head.

Bematech MP-4000 TH Quick Start User Manual

Adjusting the Paper Width Chapter 3 If you must leave printouts in the printer, bematecn aware that more than 15 tickets will increase the risk of blocking the paper exit and a paper jam may occur. Preface This manual assists you with the installation, configuration and usage of this Bematech product.


To print the manual completely, please, download it. If you must leave printouts in the printer, be aware that more than 15 tickets will increase the risk of blocking the paper exit and a paper jam may occur. Removing the Cover Lever Set To remove the lever set it is recommended that the printer cover is also removed.

Yellow LED blinking 3 times – Cutter Error Verify if there is paper between the cutter and the mechanism plastic chassis.


Page 21 MP TH. Paper Width mm You must also adjust the paper roll spacer located inside the printer, as described below: Don’t have an account? Generally, if it is green your printer is ready to print.

Introduction Introduction This manual provides information on the identification and troubleshooting, test procedures and a list of replacement parts for the MP TH printer.

Page 21 – Exploded view of the Control Board Cartr Don’t show me this message again. To remove the control board set, simply pull the cartridge back and then out.

Bematech Mp Th Fi SM SP Thermal POS Receipt USB Printer | eBay

bemafech Page 2 Bematech S. To remove the cutter sensor located at the front of the mechanism pull it to the front while opening the locks that hold the mechanism picture below, on the left.

Table of Contents Add to my manuals Add. Before turning on the MP TH, make sure that all cables are properly connected; 3.


Adjusting The Paper Width Keep it stored if in the future you will need to change back to a different paper width. This Ml4000 is used to indicate information on the current printer status. Click on the ‘Load’ button, on the ‘Update firmware’ field.

How this manual is organized Chapter 1 Knowing the product. It can be used to test the behavior of several settings in the printer, and to print in many different ways, with different resources; it can also be used to test different settings if a special application requires a fine tuning of the printer.

Tab ‘bar Code 1. nematech

To remove the paper guide, just press it by its base, disconnecting it from the metal chassis as shown on the picture on the right. This manual is intended for use by persons who are installing, using or testing the product. Page 25 – Exploded view of the Cutter Mechanism Se The printer configuration is usually compatible with many Cash Drawers in the market.

To remove the opening Lever Set, just press it from top to bottom on the points indicated on the picture. Near End Paper Sensor Configuration